ICOM i7000 User Manual Page 159
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
18
150
SPECIFICATIONS
■ General
• Frequency coverage :
Receive
30 kHz– 199.999999 MHz*
1
*
2
400–470.000000 MHz*
1
*
2
Transmit
1.800–1.999999 MHz*
2
, 3.500– 3.999999 MHz*
2
5.33050*
3
, 5.34650*
3
, 5.36650*
3
,
5.37150*
3
, 5.40350*
3
,
7.000–7.300 MHz*
2
, 10.100–10.150 MHz*
2
,
14.000–14.350 MHz*
2
, 18.068–18.168 MHz*
2
,
21.000– 21.450 MHz*
2
, 24.890– 24.990 MHz*
2
,
28.000– 29.700 MHz*
2
, 50.000–54.000 MHz*
2
,
144.000–148.000 MHz*
2
, 430.000–450.000 MHz*
2
*
1
Some frequency bands are not guaranteed.
*
2
Depending on version. *
3
USA version only.
• Mode : SSB, CW, RTTY, AM, FM, WFM
(WFM is for receive only)
•
Number of memory CH
: 503 (split memory: 99×5 banks; scan
edges: 6; call channel: 2 )
channels
• Antenna connector : SO-239
×2 (for HF/50 MHz and
144/430 MHz)
/50
•Usable temperature : –10°C to +60°C (+14°F to +140°F)
range
• Frequency stability : Less than ± 0.5 ppm
(0°C to +50°C; +32°F to +122°F)
•Power supply : 13.8 V DC±15% (negative ground)
requirement
•Current drain : Transmit (at 100 W) 22 A
(at 13.8 V DC)
Receive squelched 1.3 A
max. audio 1.6 A
•Dimensions : 167(W)
× 58(H) × 180(D) mm,
(projections not included)
6
9
⁄
16(W)
× 2
9
⁄
32(H)
× 7
3
⁄
32(D) in
• Weight (approx.) : 2.3 kg (5 lb 1 oz)
• CI-V connector : 2-conductor 3.5 (d) mm (
1
⁄8˝)
• Video connector : 2-conductor 3.5 (d) mm (
1
⁄
8˝)
• ACC connector : 13-pin
• Data connector : 6-pin
■ Transmitter
• Output power :
SSB, CW, FM, RTTY 2–100 W
(1.8–50 MHz bands)
2–50 W (144 MHz band)
2–35 W (430 MHz band)
AM 1–40 W (1.8–50 MHz bands)
2–20 W (144 MHz band)
2–14 W (430 MHz band)
• Modulation system :
SSB Balanced modulation
AM Low level modulation
FM Variable reactance modulation
•Spurious emissions : Less than –60 dB*
*spurious freq.: below 30 MHz: –50 dB; above 50 MHz: –60 dB
• Carrier suppression : More than 50 dB
• Unwanted sideband : More than 50 dB
•Microphone : 8-pin modular jack (600 )
connector
•KEY connector : 3-conductor 6.35 (d) mm (
1
⁄4˝)
• RTTY connector : 3-conductor 3.5 (d) mm (
1
⁄8˝)
■ Receiver
• Receive system :
SSB/CW/RTTY/AM/FM
Triple-conversion superheterodyne
WFM Double-conversion superheterodyne
• Intermediate frequencies:
1st
SSB/CW/RTTY/AM/FM 124.487 MHz
WFM 134.732 MHz
TV (Video) 69.0100 MHz
2nd
SSB/CW/RTTY/AM/FM 455 kHz
WFM 10.700 MHz
3rd
SSB/CW/RTTY/AM/FM 16.15 kHz
• Sensitivity (
at preamp ON):
• Squelch sensitivity
(threshold; preamp ON) :
SSB/CW/RTTY/AM Less than 5.6 µV
FM Less than 0.3 µV
• Selectivity :
SSB*
(BW=2.4 kHz) More than 2.4 kHz/–6 dB
Less than 3.6 kHz/–60 dB
CW*
(BW=500 Hz) More than 500 Hz/–6 dB
Less than 900 Hz/–60 dB
RTTY
(BW=350 Hz) More than 360 Hz/–6 dB
Less than 650 Hz/–60 dB
AM
(BW=6 kHz) More than 6.0 kHz/–6 dB
Less than 15.0 kHz/–60 dB
FM
(BW=15 kHz) More than 12.0 kHz/–6 dB
Less than 20.0 kHz/–60 dB
*IF filter shape is set to SHARP.
•Spurious and image rejection ratio:
HF bands More than 70 dB
50 MHz band More than 70 dB
(except IF/2 through)
144/430 MHz band More than 65 dB
(except IF through)
• Audio output power : More than 2.0 W at 10% distortion
with an 8 load (at 13.8 V DC)
• RIT variable range : ±9.99 kHz
• PHONES connector : 3-conductor 3.5 (d) mm (
1
⁄8˝)/8
• EXT SP connector : 2-conductor 3.5 (d) mm (
1
⁄8˝)/8
17
18
Frequency
range
[MHz]
SSB/CW/
RTTY
10 dB S/N
AM
10 dB S/N
FM
12 dB SINAD
WFM
12 dB SINAD
0.5–1.8 — 13 µV — —
1.8–28
0.15 µV 2.0 µV
— —
28–29.995
0.5 µV —
50 MHz band 0.12 µV 1.0 µV 0.25 µV —
76–108 — — — 10.0 µV
144/430 MHz
bands
0.11 µV 1.0 µV 0.18 µV
—
- INSTRUCTION MANUAL 1
- IMPORTANT 2
- EXPLICIT DEFINITIONS 2
- FOREWORD SUPPLIED ACCESSORIES 2
- ILLUSTRATIONS 3
- ■ Front panel 4
- PRECAUTIONS 5
- TABLE OF CONTENTS 6
- PANEL DESCRIPTION 10
- D Menu M-1 functions 14
- D Menu M-2 functions 14
- D Menu M-3 functions 14
- 4 function is ON, “ ” appears 15
- D Menu S-1 functions 16
- D Menu S-2 functions 16
- D Menu S-3 functions 17
- D Menu G-1 (Scope) functions 17
- ■ Microphone (HM-151) 18
- Rear panel view 19
- 12345678 19
- ■ Rear panel 20
- D DATA socket 21
- D ACC socket 21
- ■ Function display 22
- INSTALLATION AND CONNECTIONS 24
- ■ Installation 25
- KEY ACC DATA 26
- ANT2 ANT1 26
- DC 13.8V 26
- ■ Advanced connections 27
- 3.5(d) mm 27
- ■ Power supply connections 28
- ■ Battery connections 28
- ■ External antenna tuners 29
- ■ Linear amplifier connections 30
- ■ Connections for CW 31
- ■ Connections for RTTY (FSK) 32
- ■ Connections for packet 33
- BASIC OPERATION 34
- ■ VFO description 35
- ■ Selecting VFO/memory mode 36
- ■ VFO operation 36
- ■ Selecting an operating band 37
- ■ Frequency setting 38
- Programmable tuning step 39
- Selecting “kHz” step 39
- ■ Volume setting 42
- ■ Operating mode selection 43
- ■ Voice synthesizer function 43
- ■ Meter function 45
- ■ Basic transmit operation 46
- ■ Lock functions 46
- D Setting output power 47
- D Setting microphone gain 47
- RECEIVE AND TRANSMIT 48
- ■ Operating CW 50
- 4 function (p. 32) 51
- 4 function ON and OFF 51
- D CW reverse mode 52
- CW side tone function 52
- D CW pitch control 53
- ■ Electronic CW keyer 54
- • Transmitting 55
- D Memory keyer send menu 55
- Set Tx power level 59
- ■ Operating RTTY (FSK) 60
- D RTTY reverse mode 62
- Twin peak filter 62
- ■ Operating AM 66
- ■ Operating FM 68
- D Tone squelch operation 69
- D Tone scan operation 70
- D DTCS operation 71
- ■ Repeater operation 72
- D Repeater tone frequency 73
- D Auto repeater function 74
- ■ 1750 Hz tone burst 76
- ■ DTMF memory encoder 76
- Programming a DTMF code 77
- Selected 77
- D DTMF speed 77
- ■ TV channel operation 78
- Skip channel setting 79
- Channel frequency adjustment 80
- FUNCTIONS FOR RECEIVE 81
- D Center mode 82
- D Scope set mode 82
- ■ Preamp and attenuator 83
- ■ RIT function 84
- ■ AGC function 85
- ■ IF filter selection 86
- ■ Twin PBT operation 88
- ■ Noise blanker 89
- ■ Noise reduction 90
- ■ Notch function 91
- Manual notch function 92
- D Manual notch filter set mode 92
- ■ Meter peak hold function 93
- FUNCTIONS FOR TRANSMIT 94
- ■ VOX function 94
- 0 . 2 s 95
- 5 0 % 95
- ■ Break-in function 96
- TX function 97
- ■ Speech compressor 98
- ■ Monitor function 98
- COMP Level 99
- D Compression level setting 99
- ■ Split frequency operation 100
- ■ Quick split function 101
- D Quick split setting 102
- ■ Measuring SWR 103
- VOICE RECORDER FUNCTIONS 104
- D One-touch voice recording 105
- Menu selection (Example: S) 106
- Menu group selection 106
- D Recording 107
- •Erasing the recoded contents 107
- ■ Sending a recorded message 109
- ■ Voice set mode 110
- ■ Memory channel selection 111
- MEMORY OPERATION 111
- ■ Memory channels 111
- ■ Memory programming 112
- D Programming in memory mode 113
- ■ Memory channel list 114
- D Selecting a memory bank 115
- D Memory names 116
- ■ Memory clearing 117
- ■ Frequency transferring 118
- D Transferring in memory mode 119
- ■ Memo pads 120
- SCAN OPERATION 122
- ■ Programmed scan operation 123
- ■ Memory scan operation 123
- ■ Priority watch 124
- ANTENNA TUNER OPERATION 125
- ■ Optional AT-180 125
- ■ Optional AH-4 126
- PACKET OPERATION 127
- CLOCK AND TIMERS 128
- D Setting the current year 129
- D Setting the current date 129
- D Setting the current time 129
- D Auto power OFF activity 130
- D Clock2 function activity 130
- D Clock2 offset setting 130
- SET MODE 131
- ■ Quick set mode 132
- Quick set mode (continued) 133
- ■ Display set mode 135
- Display set mode (continued) 136
- ANTENNA TUNER 141
- To [MIC] connector pin e 146
- To [MIC] connector pin u 146
- V LEVEL CONVERTER 147
- MAINTENANCE 148
- TROUBLESHOOTING 149
- TRANSMITDISPLAYSCAN 150
- POSSIBLE CAUSE SOLUTION REF 150
- OPTION UNITS SETTING 151
- ■ MB-106 151
- CARRYING HANDLE 151
- CONTROL COMMAND 153
- • Command table (continued) 154
- SPECIFICATIONS 159
- MENU GUIDE 162
- MENU/GRP)] or [AF] switch 163
- A-6241H-1EX 166
- Printed in Japan 166
- © 2005 Icom Inc 166
© 2020, manymanuals.com. All rights reserved. | 1.744 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals